A lot of microscopic tracks that needed to be cleaned up in your KiCad PCB project might end up messing with your DRC report: You just need to select and delete the culprit, then DRC gets cleared: Hope this helps. Greetings !
Motor drivers for antenna rotator
I made some progress on my antenna rotator project and installed the stepper drivers and the Raspberry Pi computer. I bought two drivers from ardushop.ro and these should work just fine. They are based on Toshiba TB6560AHQ, PWM Chopper-Type Bipolar Driver IC for Stepping Motor Control. The datasheet can be downloaded from here. My projects […]
Mini N connector – timelapse in Fusion360
I needed this 3D design for a mini N connector that I have in my shack but I was unable to find any 3d file (.STEP etc) online. The connectors are used for my 101dB attenuator project. Enjoy ! Greetings.
Project status – 3D printed antenna rotator (16/09/2021)
My 3D printed antenna rotator project for ham radio satellites. Status 09/16/2021
Project status – 3D printed antenna rotator (12/09/2021)
This is a short video about the progress of my 3D printed antenna rotator. Unfortunately only in romanian for now, but captions will be created soon.
Kicad & Autodesk Fusion 360
I published on YouTube a video about how to export ecad files in KiCad and import them in Autodesk Fusion 360 to create nice electromechanical assemblies. Captions in english.
Short Assembly test in Fusion 360: RoLink + Raspberry
A very short clip with assembly test in Autodesk Fusion360: Raspberry Pi and a hat I designed for mobile radio. This type of simulation is extremely useful to pin point issues in mechanical design and assemblies (see at 0:35), that can be avoided early in the manufacturing process. I will create a more detailed tutorial […]
Build SvxLink on Orange Pi — aide-mémoire
This is mostly a memory helper, to remind me some steps in the setup of Svxlink on Orange Pi Load packages sudo apt update sudo apt install g++ cmake make libsigc++-2.0-dev libgsm1-dev libpopt-dev tcl8.5-dev libgcrypt20-dev libspeex-dev libasound2-dev libopus-dev librtlsdr-dev doxygen groff alsa-utils vorbis-tools curl libcurl4-openssl-dev git rtl-sdr libcurl4-openssl-dev Create svxlink user and add to groups […]
Build SvxLink on Raspberry — aide-mémoire
This is not really a post, but mostly a reminder with some information to help me remember the steps. Meanwhile I wrote a much more extensive documentation here, on my wiki (in romanian). And I think I also made a video tutorial but I have to upload it to YouTube. Load packages sudo apt update […]
First steps with Orange Pi
This is rather a reminder, not a real post. This is a collection of links to help me in my quest to control this device.
Tuzla 2020, Field day
I published on my YouTube channel a video about the ham radio Field Day event at Tuzla, Romania, 2020.
Genetic algorithm mutation coded in Python
This example is adapted from Clinton Sheppard’s excellent book “Genetic Algorithms with Python“, a book that I encourage you to buy and read. The very simple example shows how easy is to design in Python a simple mutation algorithm that merges to the optimal solution in 24 iterations. The example below uses romanian language accents […]
KiCad Templates for Orange Pi Zero
KiCad templates for two different hat models for Orange Pi Zero boards can be downloaded from my GitHub repo. Two different KiCad templates can be downloaded in the same GitHub archive: one uncut, 46×48 mm exactly same size as Orange Pi Zero; the other one has some cuts for network and USB connector, to accomodate […]
LTSpice simulation of Baofeng UV5R band selector
I was quite busy the other day trying to understand how Baofeng is using RDA1846 transceiver in their products. While analyzing the schematic it struck me the overcomplicated way they do the switch between UHF and VHF. This is an excerpt of the schematic: The entire selector block is made up with discrete components ! […]
Jabra Evolve 65 repair
A couple of weeks ago during what should have been a routine firmware upgrade, my Jabra Evolve 65 simply died. Have no idea what happened and maybe that will make an interesting future project, but because this headphone is my main headset used for teleconferences and other communication required by my job, I was kind […]
Kenwood THD74 measurements
Some RF power masurements done with my Rigol DS 815TG of my Kenwood THD74.
KiCAD, Python and PyCharm
I am not a huge fan of KiCad. However, given the limited and abysmal options that we have for free EDA packages, KiCad is quite ok, although terribly flawed in some areas. Maybe the development team should focus on some simple functionalities like support for rounded traces, net group routing, zones, a simple way to […]
How to start with FPGA
The title of this post might seem a bit too pretentious because it might imply that I am in the position to provide the ultimate recipe on how to train yourself into FPGA. However, it is more like a review on how I did it and some advices based on my limited experience. But this […]
Quartus files
One of the biggest issues that I have, in general, while learning different stuff is lack of properly-explained abbreviations. I am starting today a compilation of Altera/ Intel Quartus list of filenames and abbreviations. Source: Intel/ Altera Glossary .qws – Quartus Workspace File. The Quartus® Workspace File (.qws) is a non-editable file that stores user […]
Time Capsule Repair
Some time ago, my old Time Capsule died. It simply did not start. I read that this is an issue that plague all older (first and second generation) TCs. The culprits are four electrolytic capacitors inside the switching power supply, two 1,500 µF, one 1,000 µF and one 470 µF. The 1,500 µF were badly swolen. […]
AD8307 RF Power Meter III — build
This will be another short post. I also made the GitHub repo public, but please be aware, current design is flawed. If you use it, you acknowledge that you use it on your own risk. Today I managed to build the revision 1.0 of this power sensor, not without some lessons learned. It was my […]
AD8307 RF Power Meter II — boards from JLPCB
I ordered the boards for this project with JLCPCB in China. This is my first attempt of working with a professional PCB manufacturer and I am extremely pleased by the results.
AD8307 RF Power Meter
My first finished KiCad project is a prototype of a RF Power meter with input attenuation built around an Analog Device AD8307. An excellent tutorial about log amps can be read in March 1999 edition of Analog Dialogue. KiCad PCB: And the 3D rendering of the same PCB: The next step will be PCB ordering, […]
How to install Python 3.7 on Raspberry Pi
This short guide explains how to install Python version 3.7.0 on a Raspberry Pi running Raspbian. First, get rid of old versions: Ensure system is up to date: Install the dependencies needed for building the distribution: build-essential tk-dev libncurses5-dev libncursesw5-dev libreadline6-dev libdb5.3-dev libgdbm-dev libsqlite3-dev libssl-dev libbz2-dev libexpat1-dev liblzma-dev zlib1g-dev libffi-dev Get the python src distribution: […]
Altera Qsys, NIOS II and FPGA fun
One very interesting feature of Altera FPGAs is that almost any system can be created in its next-generation system integration tool Qsys using a standard library of reusable IP blocks. The system interconnect fabric is automatically generated by Qsys and binds the blocks together. The system interconnect manages dynamic bus with matching, interrupt priorities, arbitration […]
End of week — pin planner
This week was quite busy to complete my assignments for the FPGA Course. I was running out of time because I did not estimate properly my available free time and things got crowded at the office, at this end of week. With a lot to do there, I barely found any time to focus on […]
FPGA Course
I’ve been quite busy lately and neglected the blog. I enrolled on Coursera for a very interesting FPGA course, in what seems to be a FPGA specialization from University of Colorado Boulder. I have always had somewhat a reserved attitude towards FPGAs mainly because I believed that these are hard to understand and need a […]
Error opening serial port
Encouraged by the latest developments, today I started building a new application that will allow remote connection to Kenwood TH-D74, remote control and APRS data transfer. However, while building and running the app I got the following error: If you encounter this, be aware that it is generated by application sandboxing. You can think of using […]
TH-D74 BLE or “Bluetooth Low Energy”
Struggling to understand how Universal Unique IDs work (see here) I was wrongly assuming that Core Bluetooth is a framework from Apple that covers all aspects of communication with devices via BT. I was WRONG ! scanForPeripheralsWithServices method and, in general, what I tried to do, for almost a week, is NOT good for my intended […]
Using UUIDs and Bluetooth
I did some more steps towards accessing Kenwood TH-D74’s services via bluetooth. I struggled for some time understanding how discovery based on UUIDs work. I was not aware that, for each service profile, there is a standard Universally Unique Identifier (UUID) documented in Bluetooth SIG specs. Specifically for Serial Port Profile (SPP) service, the UUID […]